城市污泥-磷石膏陶粒的制备条件及性能分析

以城市污水处理厂剩余污泥和磷酸生产废渣磷石膏为原料制备多孔陶粒,考察不同配比、烧结温度及烧结时间对多孔陶粒堆积密度、吸水率及盐酸可溶率的影响。结果表明:在污泥与磷石膏混合比1∶4、烧结温度1 050℃、烧结时间15 min的条件下,可制得堆积密度为685.78 kg/m~3、吸水率27.34%、盐酸可溶率11.38%的陶粒,该陶粒内部含有丰富的膨胀气孔,可用作水处理滤料或建材骨料。     

基于TiO2载体的锰铈系低温SCR脱硝催化剂研究进展

开发低温、高活性、高抗硫抗水性能的选择性催化还原(SCR)脱硝催化剂已成为国内外的研究热点。综述了基于TiO2载体的锰铈系低温脱硝催化剂的脱硝性能,探讨了助剂掺杂改性、制备方法、反应条件等对催化剂脱硝性能的影响,总结了现有低温脱硝催化剂的技术难点,指出SCR催化剂的研究需要着重考虑以下几方面:深入研究催化剂的反应机理和中毒机理;研究催化剂的循环再生;探究拓宽催化剂温度窗口,使其适应不同的温度条件。     

肥煤自燃全过程热动力学特征参数研究

实验测定了林西矿肥煤样品30~900℃煤自燃全过程热动力学特征参数,得出:TG/DTG曲线显示煤样DTG初始临界温度45℃,干裂温度122℃,活性温度195℃,增速温度265℃,质量极大值温度342℃,着火温度465℃,最大热失重速率温度515℃和燃尽温度690℃;DSC曲线显示,煤样初始放热温度60℃、最大热释放速率温度511℃。结合TG-DTG-DSC曲线综合分析可知,煤温达到510℃左右时煤样反应最剧烈。由煤自燃标志气体测定实验系统得出:煤温130℃后CO,CO 2释放量迅速增加,210℃增加速度下降;CH 4,C 2 H 6含量变化具有规律性且两者变化相近;C 2 H 4出现温度为130℃;C 2 H 4/C 2 H 6比值在190~350℃有较强的规律性,呈上升趋势且上升速度较快;350℃之后,CH 4,C 2 H 6,C 2 H 4体积分数均开始急剧增大;C 2 H 4/CO与C 2 H 4/CO 2变化趋势大致相同,在130~350℃时缓慢增长,达到350℃后比值呈指数形式上升。经拟合曲线,得到活化能的3个突变点温度:70,180,220℃,其中180℃与交叉点温度相吻合。通过以上研究,得到了肥煤自燃全过程的热力学特征参数,为实际生产中防治煤自燃提供了理论依据。     

屏蔽服冷却系统对人体表面温度影响的研究*

为科学有效地论证多种方式组合的冷却屏蔽服在不同环境条件下对人体表面温度控制的效果，需要对冷却系统及人体敏感部位发热量进行客观评估。通过对5名健康男性的高温测试，探究人体在不同环境温度下体表温度的变化，得出胸部、背部及额头为热量最高部位，并构建以“人体-降温屏蔽服-外界环境”为主体的冷却系统数值模型，对不同环境中的屏蔽服冷却效果展开研究，分析穿戴冷却屏蔽服时人体躯干部分的温度分布及影响。结果表明:在屏蔽服中靠近胸部、背部部位引入相变材料和风扇，均可帮助人体降低体温，提高舒适度。     

Development of machine learning based prediction models for hazardous properties of chemical mixtures

Lower flammability limit (LFL), upper flammability limit (UFL), auto-ignition temperature (AIT) and flash point (FP) are crucial hazardous properties for fire and explosion hazards assessment and consequence analysis. In this study, a comprehensive prediction model set was constructed by using expanded chemical mixture databases of chemical mixture hazardous properties. Machine learning based gradient boosting quantitative structure-property relationship (GB-QSPR) method is implemented for the first time to improve the model performance and prediction accuracy. The result shows that all developed models have significantly higher accuracy than other regular QSPR models, with the 5-fold cross-validation RMSE of LFL, UFL, AIT, and FP models being 1.06, 1.14, 1.08, and 1.17, respectively. All developed QSPR models can be used to estimate reliable chemical mixture hazardous properties and provide useful guidance in chemical mixture hazard assessment and consequence analysis.     

The determination and matching analysis of pinch point temperature difference in evaporator and condenser of organic rankine cycle for mixed working fluid

Exergo-economic analysis of the pinch point temperature difference (PPTD) in both evaporator and condenser of sub-critical organic Rankine cycle system (ORCs) are performed based on the first and second laws of thermodynamics. Taking mixture R13I1/R601a as a working fluid and the annual total cost per net output power Z as exergo-economic performance evaluation criterion, the effects of PPTD in evaporator ΔT_e, and the PPTD ratio of condenser to evaporator y, on the exergo-economic performance of ORCs are analyzed. Moreover, how some other parameters influence the optimal PPTD in evaporator ΔT_e,opt and the optimal PPTD ratio of condenser to evaporator y_opt are also discussed. It has been found that the exergo-economic performance of ORCs is remarkably influenced by ΔT_e and y, and there exists ΔT_e,opt and y_opt. In addition, ΔT_e,opt and y_opt are affected by heat transfer coefficient ratio of condenser to evaporator ß, the temperature of working fluid at dew point in condenser T_1a, and composition of R13I1/R601a: larger ß and T_1a lead to lower ΔT_e,opt and y_opt; by contraries, larger mass fraction of R13I1 makes ΔT_e,opt and y_opt increase, and y_opt increases linearly. The effects of the temperature of working fluid at bubble point in evaporator T_3a, mass flow rate of exhaust flue gas m_g, and inlet temperature of exhaust flue gas T_gi on ΔT_e,opt and y_opt are very slight. For comparison, three additional working fluids, namely R601a, R245fa, and 0.32R245fa/0.68R601a, are also taken into account.     

烟气脱硫溶液中硫酸根的去除

分别采用石灰乳化学沉淀法和低温结晶法去除烟气脱硫溶液中的SO42-。实验结果表明：在室温、CaO溶液质量分数25%的条件下，石灰乳化学沉淀法对SO42-的去除率仅为59.51%，且向溶液中引入了Ca2+，产生的硫酸钙固体废物难以再生利用；采用低温结晶法处理烟气脱硫溶液，在结晶温度7 ℃、结晶时间3 h、NaOH加入量34.8 g/L的条件下，SO42-的去除率为82.04%、滤液中的ρ（Na+）为3.88 g/L。在现场工业应用试验中，采用低温结晶法去除烟气脱硫溶液中的SO42-，平均SO42-的去除率可达70.00%以上，滤液中的ρ（Na+）小于15.00 g/L。该法可有效抑制烟气脱硫溶液中SO42-含量的增加。     

常温条件下2种厌氧折流板反应器处理淀粉废水的启动实验

为了研究厌氧折流板反应器在常温下的启动情况,在22.5～30.2℃条件下,对不加填料的5隔室厌氧折流板反应器和加填料的4隔室复合式厌氧折流板反应器同步进行了启动实验。实验用水为高浓度淀粉废水,两反应器采用相同的启动策略,即梯度增加进水COD浓度与降低水力停留时间相结合的方式。两反应器有效容积均为47.8 L,启动初始负荷为0.6 kg COD/(m3.d),逐渐增加到10 kg COD/(m3.d)。实验表明,经过6个阶段87 d的运行,反应器启动完成,并成功培养出颗粒污泥,两反应器对COD的去除率都能达到85%以上。在启动过程中两反应器对COD的去除效率相近。